DigiTech HARDWIRE CR-7 Manuel du propriétaire

Naviguer en ligne ou télécharger Manuel du propriétaire pour Pédale de musique DigiTech HARDWIRE CR-7. DigiTech HARDWIRE CR-7 Owner`s manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer

Résumé du contenu

Page 1 - STEREO CHORUS

HARDWIRE CR-7STEREO CHORUSOWNER’S MANUAL

Page 2 - DECLARATION OF CONFORMITY

45. Type Knob - The Type knob selects one of the seven chorus types: • STUDIO – Studio quality chorus with a wide stereo image.• MULTI – True 8-v

Page 3 - COMPATIBILITY

57. Input 2 - Connect a second input to this jack for stereo operation. Inputs 1 and 2 are processed separately through the stereo chorus effect and

Page 4 - WARRANTY:

611. Output 1 (Mono) - Connect this output to the input of a single guitar amplifier, another pedal input, or an amp effects return. 12. Output 2 -

Page 5 - Congratulations!

7Amp SetupHarman PowerSupply (optional)or

Page 6

8Effects Loop SetupAMP RETURNAMP SENDHarman PowerSupply (optional)Note: If the amp effects loop has a mix control, set the mix to 100% full wet.

Page 7 - Included Items

9Battery OperationIn the event that battery power is completely depleted, HardWire pedals automatically switch into bypass. This eliminates the need t

Page 8 - Pedal Interface

10into place over the depressed pin. Release the pin. When the Foot Switch is properly fastened, both Release Pins are flush with the outer side of th

Page 9 - What Does This Do?

11Performance AccessoriesThe performance accessories make integrating a HardWire pedal into any pedal board a snap. The following accessories are incl

Page 10

12Hook-and-loop Pedalboard PadTo attach the Pedalboard Pad, do the following:1. Peel off the existing rubber skid pad from the bottom of the pedal.2.

Page 11

13Foot Switch Glow StickerTo attach the Foot Switch Glow Sticker, do the following:1. Peel the adhesive backing from the Foot Switch Glow Sticker.2.

Page 12

DECLARATION OF CONFORMITYManufacturer’s Name: Harman Signal ProcessingManufacturer’s Address: 8760 S. Sandy Parkway Sandy, Utah 84070, USAdeclare

Page 13 - Supply (optional)

14StompLockTo place the StompLock over the pedal knobs, do the following:1. Set the knobs to your preferred setting.2. Gently push the StompLock ove

Page 14 - AMP SEND

15SpecificationsControls: Level, Speed, Depth, Type, On/Off PedalJacks: Input 1 (Mono), Input 2, Output 1 (Mono), Output 2Input Impedance: >1 MΩ

Page 17 - Performance Accessories

8760 South Sandy ParkwaySandy, Utah 84070PH (801) 566-8800FAX (801) 566-7005 DigiTech® and HardWire® are registered trademarks of HarmanDesigned in th

Page 18 - Hook-and-loop Pedalboard Pad

WARNINGFor your protection, read the following:Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warni

Page 19 - Foot Switch Glow Sticker

WARRANTY: We at DigiTech® are very proud of our products and back-up each one we sell with the following warranty:1. Please register online at www.d

Page 20 - StompLock

Congratulations!You have just purchased a DigiTech® digital effect pedal.Unlike many analog pedals, the number of hours digital pedals can be powered

Page 22

1IntroductionMore than a remarkable achievement, DigiTech’s HardWire® series represents a collection of significant improvements in guitar effects ped

Page 23

2Pedal Interface2 3 4 5678111289101

Page 24

3What Does This Do?1. Level Knob - Controls the chorus level. Turn this knob clockwise to increase and counter-clockwise to decrease the chorus level

Commentaires sur ces manuels

Pas de commentaire